A pool table is an elegant design used for indoor sports rooms and patios. The game of pool is played as a way of spending leisure time with friends and family. If the tables were to be made of materials that are durable, they can last around twenty years with less maintenance. The most vulnerable component of the structure is the felt. In consideration of pool table refelting Denver residents should know the procedure.
The felt is the fabric which is attached to the surface of the table. When re-felting, the first step is to determine the size of the pool table using a measure tape. The felt is then replaced at a sports shop or home improvement depot. The material should be purchased such that there is an extra 12 inches to the width and length. Because there are many colors, it will be important to decide if the same color as the one being replaced will be used or a different one.
The next step is to remove the rails. The tool used for this exercise is the crescent wrench. You should also remove the bolts that attach the rails. Normally, the rails are also covered by felt material and thus will have to be re-felted as well. The rails are then set on the floor carefully next to its position on the table. This is so done as to avoid making any errors when attaching them back. They may be attached on the wrong side.
The felt that needs to be replaced gets removed using a staple remover. It is used for pulling out the staples at the felt edge. Caution should be taken to ensure there is removal of all felt from the surface of the table. The old felt should be placed on a thrash bag and disposed of later.
The new one is carefully placed while being cautious not to damage or stain it. During the process, a sharp pair of scissors is used to cut it. The borders of the table are used as the guide. There needs to be some felt left over that is to be used to re-felt the rails.
After making the cut, a stapler is used to attach the felt to the top of the table. Stapling begins at the mid points of one end of the felt then proceeds to the left and right edges. When this is done, you proceed to the other end to pull the felt tightly. It then gets stapled like was done in the previous case.
Side edges are then stapled. It is essential to ascertain that the staples are placed at the same distance from each other. They also need to be lined up in the correct way. 3 slits are cut on each pocket then the felt is wrapped and stapled on the pocket edges. Before stapling, the felt is tightly pulled.
The last step is to reassemble the structure. The rails are attached to their proper position using the crescent wrench. After insertion of the pocket lines, the re-felted table can be used.
The felt is the fabric which is attached to the surface of the table. When re-felting, the first step is to determine the size of the pool table using a measure tape. The felt is then replaced at a sports shop or home improvement depot. The material should be purchased such that there is an extra 12 inches to the width and length. Because there are many colors, it will be important to decide if the same color as the one being replaced will be used or a different one.
The next step is to remove the rails. The tool used for this exercise is the crescent wrench. You should also remove the bolts that attach the rails. Normally, the rails are also covered by felt material and thus will have to be re-felted as well. The rails are then set on the floor carefully next to its position on the table. This is so done as to avoid making any errors when attaching them back. They may be attached on the wrong side.
The felt that needs to be replaced gets removed using a staple remover. It is used for pulling out the staples at the felt edge. Caution should be taken to ensure there is removal of all felt from the surface of the table. The old felt should be placed on a thrash bag and disposed of later.
The new one is carefully placed while being cautious not to damage or stain it. During the process, a sharp pair of scissors is used to cut it. The borders of the table are used as the guide. There needs to be some felt left over that is to be used to re-felt the rails.
After making the cut, a stapler is used to attach the felt to the top of the table. Stapling begins at the mid points of one end of the felt then proceeds to the left and right edges. When this is done, you proceed to the other end to pull the felt tightly. It then gets stapled like was done in the previous case.
Side edges are then stapled. It is essential to ascertain that the staples are placed at the same distance from each other. They also need to be lined up in the correct way. 3 slits are cut on each pocket then the felt is wrapped and stapled on the pocket edges. Before stapling, the felt is tightly pulled.
The last step is to reassemble the structure. The rails are attached to their proper position using the crescent wrench. After insertion of the pocket lines, the re-felted table can be used.
Aucun commentaire:
Enregistrer un commentaire