One of the popular trends in eye wear these days are known as the clip on flip up sunglasses because these things can actually replace actual sunglasses with the same quality. Now one many do not know is that it is actually possible to make this kind of accessory instead of going out to a store and buying one. Now if one is interested in trying to create one of these things, then try following some of these steps.
The first step would be to get hold of an old pair of sunglasses and use a small screwdriver to take the arms of the glasses out. When one does this, then all that will be left would be a pair of lenses of the sunglasses. Take note that the pair of glasses right now is very delicate and may break if not handled well.
The next thing to do would get an old paper clip that is rather hard and a pair of pliers. Now the thing that one should do with the paper clip would be to straighten it out using the pliers. Remember to straighten it out slowly and carefully because it is possible that the paper clip might break.
When the wire has been straightened, then one should get a pair of tough scissors and try to cut the wire into two. Then the next thing to do would be to get a wire and try to put it into the hole where the arms of the glasses was taken out. He must also do this for the other hole.
After this is done, then one must now take the pliers and try to tie the wires to the holes so that it stays there. Take note that it is extremely hard to tie the wire to the hole by hand so do not even try to attempt that. One must also make sure that the knot is very tight because if it is not, then it is possible that the wire will be really loose.
After that, one should now bring the two ends of the wire to the top middle of the glasses. Now one should make sure that the wire is attached to the frame so that the wire will not be seen by the wearer. From there, one should make a knot using the two ends of the paper clip so that it will stay steady.
When a small knot has already been formed, then the next part would be to curve the wire a little bit. This little curve will be the one that will be attached to the very center of the glasses. When everything fits well, then it may now be worn outside.
So as one can see, it is actually very easy to make a pair of clip on flip up sunglasses. The great thing about this device is that it is very practical because it is easier to use than a normal pair of sunglasses. It is also much cheaper to make one at home because the ones outside are very expensive.
The first step would be to get hold of an old pair of sunglasses and use a small screwdriver to take the arms of the glasses out. When one does this, then all that will be left would be a pair of lenses of the sunglasses. Take note that the pair of glasses right now is very delicate and may break if not handled well.
The next thing to do would get an old paper clip that is rather hard and a pair of pliers. Now the thing that one should do with the paper clip would be to straighten it out using the pliers. Remember to straighten it out slowly and carefully because it is possible that the paper clip might break.
When the wire has been straightened, then one should get a pair of tough scissors and try to cut the wire into two. Then the next thing to do would be to get a wire and try to put it into the hole where the arms of the glasses was taken out. He must also do this for the other hole.
After this is done, then one must now take the pliers and try to tie the wires to the holes so that it stays there. Take note that it is extremely hard to tie the wire to the hole by hand so do not even try to attempt that. One must also make sure that the knot is very tight because if it is not, then it is possible that the wire will be really loose.
After that, one should now bring the two ends of the wire to the top middle of the glasses. Now one should make sure that the wire is attached to the frame so that the wire will not be seen by the wearer. From there, one should make a knot using the two ends of the paper clip so that it will stay steady.
When a small knot has already been formed, then the next part would be to curve the wire a little bit. This little curve will be the one that will be attached to the very center of the glasses. When everything fits well, then it may now be worn outside.
So as one can see, it is actually very easy to make a pair of clip on flip up sunglasses. The great thing about this device is that it is very practical because it is easier to use than a normal pair of sunglasses. It is also much cheaper to make one at home because the ones outside are very expensive.
Aucun commentaire:
Enregistrer un commentaire